[W126 Coupe] Console Rubber

[Eddie]

Are you kidding me? $400 would be barely enough to make the mold, not yet
cover material, shipping, and time.

 

Eddie

 

  _____  

From: mbcoupes-bounces at mbcoupes.com [mailto:mbcoupes-bounces at mbcoupes.com]
On Behalf Of Shayegan, Richard
Sent: Tuesday, November 15, 2005 5:23 PM
To: Mercedes Coupes Mailing Lists
Subject: RE: [W126 Coupe] Console Rubber

 

What about having somebody run a batch of new rubber surrounds? I bet with
$400 you could get someone to make 1000 of them, and then sell them to list
members for $1.39 (.39 for the new 1st class standard shipping rate). I'm
sure there are list members who know people who own metal fabrication
shops.how about a rubber fabrication shop?

 

  _____  

From: mbcoupes-bounces at mbcoupes.com [mailto:mbcoupes-bounces at mbcoupes.com]
On Behalf Of Jonathan Hodgman
Sent: Tuesday, November 15, 2005 8:11 PM
To: Mercedes Coupes Mailing Lists
Subject: Re: [W126 Coupe] Console Rubber

 

This part has been NLA for a LONG time..  The 6/89 and later have the hard
plastic insert that takes the place of the rubber..  The hole on the later
pieces of wood is a Good bit bigger then the earlier style and I doubt if
the plastic would look/fit well no matter the modification.

There is no simple/satisfactory way to handle this other then purchasing new
wood.

Jonathan

On 11/15/05, Dick Spellman <spell.yy at verizon.net> wrote:

If the only way MB sells the rubber surround insert for the console shift
gate is attached to a $400 piece of veneer, you may want to try and measure
the overall cut-out size and compare this to the 126 later year sedans.  The
sedans use a plastic surround with four pressure slots that fit between
console wood and shift gate enclosure.  What's more this plastic rim sort of
folds over onto the surface of the console wood where the original rubber
flushes up to the wood's edge and sits more on the shift gate.

 

If the measurements are close you could just try cutting off the pressure
tabs and see if it will sit in place with a dab or two of black silicon.
'If it does not fit you must errrquit' and figure out another solution.  I
figure this may be worth a try.  I'll do a test fit of the sedan plastic on
my coupe when I get a chance the end of the week.

 

Dick


The MB Coupes Website!
W126 SEC Mailing List
Postings remain property of MB Coupes, L.L.C.




-- 
Need Parts? I won't sell anything I wouldn't install on my own car. 
Live in Atlanta? I can service/modify/treat your car as if it were my own.
Mechanical, Cosmetic and Mobile Audio/Video

http://jono.mbfans.net/Index.htm

1991 560SEC 110K Full Euro ECE, 
1991 560 SEC 127K White on gray 226Hp/271ft/lbs:)
1989 560SEC AMG (N.America Coversion)
1986 560 SEC Currently being Parted(check my page)
1986 560 SL 140K White on Burgandy
1985 500 SEL Euro Parts Car
1985 300 CD 150K Blue on Blue (and rust free!)
1880 280 SE Euro 150K
1978 300D "The Yellow Turd" TMU
1996 S600 Euro 34K "Scharnhorst"
1987 560 SEL 162K Midnight Blue on Gray RIP:(
1992 E300D 140K Champagne on Parchment tex (Sold) 
1990 560 SEC 154K Anthracite on Gray (Sold)
1980 280 SE US 185K (Sold)
1988 300 TE 160K Burgundy on Palomino (Sold) 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://www.pairlist.net/pipermail/mbcoupes/attachments/20051115/ff1246ed/attachment.html